产品详情
  • 产品名称:U型系列可调多轴器(重切削)

  • 产品型号:
  • 产品厂商:丰正机械
  • 产品价格:0
  • 折扣价格:0
  • 产品文档:
你添加了1件商品 查看购物车
简单介绍:
◎本体结构利用齿轮箱配合万向节头所组成,容易调整加工孔距不受齿轮所限制,节省调整的时间,也少有死角的限制。其齿轮、轴承、输出轴、万向节均采用强力系列,适合加工钢件等强力场合。为保万向节头之寿命,移动范围不得超过15度,等于垂直之前後左右30mm以内。 (尽量配合工作之孔距坐标,设计齿轮箱结构即定镗孔位) ◎The basic frame consists of gear case and cardan joint.The hole-distance is easy to control and will not be affected by the gears.The set up time is thus saved and it is mostly free of dead angles.It is very suitable for working of round holes.
详情介绍:

U型系列可调多轴器(重切削)

其齿轮、轴承、输出轴、万向节均采用强力系列,适合加工钢件等强力场合。利用齿轮箱配合万向节头所组成,容易调整加工孔距不受齿轮所限制,节省调整的时间,也少有死角的限制。为保万向节头之寿命,移动范围不得超过15度,等于垂直之前後左右30mm以内。

(尽量配合工作之孔距坐标,设计齿轮箱结构即定镗孔位)

※万向节注意事项

1.调整时不能超过规定的角度15度

2.如超过此极限心轴易磨损或断裂

3.工作时应经常加润滑油脂

※Note of cardan Joint

1.Do not set the angle to more than the specifled l5 degrees.

2.If the limit is exceeded,the shaft will be easy to wear or break.

3.During work,lubrication should be added frequently.

型号 Type

SWU165

SWU200

SWU250

SWU100×165

SWU120×200

SWU120×300

筒夹规格Collet/

*大钻孔能力

Max.Drilling Capacity

ER20/13

ER25/16

ER20/13

ER25/16

ER20/13

ER25/16

ER20/13

ER25/16

ER20/13

ER25/16

ER20/13

ER25/16

转速比

Gear Ratio

1∶1

1∶1

1∶1

1∶1

1∶1

1∶1

*小距离(二轴间)

Lowest Distance(Two Spindle)

42

42

42

42

42

42

*大轴心范围

Max.Range of Centers

165

200

250

100×165

120×200

120×300

轴数

Spindle

2-10

4-12

4-12

3-8

4-12

6-14

标题:
内容:
联系人:
联系电话:
Email:
公司名称:
联系地址:
 
 
注:1.可以使用快捷键Alt+S或Ctrl+Enter发送信息!
2.如有必要,请您留下您的详细联系方式!
相关文章

渝公网安备 50011202503181号